This protocol allows communicating with the bootloader running on an attiny or other small microcontroller, through I²C. It is intended to support a composite embedded system, where a single mainboard controls a number of child boards connected to a shared bus. This protocol then facilitates the mainboard uploading an application to each child bus and then executing that application.
This document describes protocol version 2.1 (0x0201).
The initial version of this protocol was intended to be used over I²C only to allow the bootloader to share the same bus as the SSD1306 display it was connected with. The initial bootloader implementation used the low level I²C implementation and framing from the "bootloader-attiny" by Erin Tomson from Modulo, but the upper layer of the protocol (the available commands) were redesigned from scratch.
The intended usecase for this protocol and bootloader is a integrated system with a single master controller, with multiple attached child controllers:
- At poweron, each child starts the bootloader. This bootloader listens on the bus for commands for the master. There is no timeout, so the bootloader will just wait if the master does not send any info.
- The master detects all children, assignes each a unique address and uploads an application to each. This happens again on every boot (though the child takes care to prevent a flash erase and write cycle when the data is identical).
- The master tells the child to start the application.
So this protocol is explicitly not intended to be used on standalone boards, to upload software from a computer or so.
Initially, only the I²C bus was supported, but since that bus is prone to noise problems when used for off-board connections, RS485 support was later added. The upper layer of the protocol is identical between I²C and RS485, but the lower level (framing) is different.
For RS485, the framing is copied from ModBus, which ensures that this protocol can be used on a bus where ModBus is also used, without any conflicts (provided that distinct addresses are used). That is, from the point of view of other ModBus servers, all ChildBus messages look like valid ModBus messages addressed to someone else. The intention is explicitly not to allow using a complete ModBus client implementation to communicate with a Childbus child.
Note that the physical layer is intended to be RS485, but any (minimally) half-duplex byte stream that provides the necessary timing can be used (i.e. TTL serial is fine, TCP is not).
All transactions take the form of a write transfer (command plus arguments), followed by a read transfer (status plus command result).
A write transfer consists of: A command byte, any number of argument bytes and one CRC byte.
A read transfer consists of: A status byte, a length byte, any number of result bytes and one CRC byte.
Visually, this looks like the following. A white background indicates the line is controlled by the master, a gray background indicates the line is controlled by the child.
| Start | address+W | command | argument bytes... | CRC | Stop (optional) | |
| Start | address+R | status | number of result bytes | result bytes ... | CRC | Stop |
Acks and nacks are omitted from this table, but are present after each byte. All bytes should be acked by the other party than the one that sent the data. The last byte in a read transfer should always be acked by the master, so the child knows to release the bus.
The maximum length of a transfer is variable, see the
GET_MAX_PACKET_LENGTH command for more details.
The number of result bytes in the transfer indicates the number of result bytes, excluding the the status, the number itself and the CRC.
The master should either look at the length byte to know how much bytes to read, or it should make sure to read enough bytes so all possibly expected replies would fit. If the master is unable to look at the length byte during the transfer and thus reads more bytes than the child has available, the child should just return arbitrary values. The master should ignore these by looking at the length byte after the transfer. Alternatively, it could do a short read first, look at the length byte and then do a longer read to get the full reply.
The CRC is calculated over all bytes, except the address byte.
Like with ModBus, the serial settings can be varied depending on the needs of the network. The default settings are 19200 bps, one start bit, 8 data bits, even parity and one stop bit.
ModBus uses an interframe timeout (t3.5) which is nominally the length of 3.5 bytes up to 19200 bps, but is specified as a fixed 1750μs for higher baudrates.
In practice, these default settings (19200 bps and 1750μs t3.5) result in excessive transfer times when uploading bigger flash contents (38 seconds for transferring 64k), so using a higher baudrate and/or lower interframe timeout is recommended.
ModBus also specifies a maximum interbyte spacing (t1.5), considering a message invalid if this maximum spacing is exceeded inside a frame. To simplify implementations, a child does not need to check this spacing, though a master should comply with it.
All transactions take the form of a request (master-to-child, command plus arguments), followed by a reply (child-to-master, status plus command result).
A request consists of: An address byte, command byte, any number of argument bytes and two CRC bytes.
A write transfer consists of: An address byte, a status byte, a length byte, any number of result bytes, and one CRC byte.
Visually, this looks like the following. A white background indicates the line is controlled by the master, a gray background indicates the line is controlled by the child.
| address | command | argument bytes... | CRC LSB | CRC MSB | |
| address | status | number of result bytes | result bytes ... | CRC LSB | CRC MSB |
The maximum length of a request or reply is variable, see the
GET_MAX_PACKET_LENGTH command for more details.
The number of result bytes in the transfer indicates the number of result bytes, excluding the address, the status, the number itself and the CRC.
The CRC is calculated over all bytes, including the address byte (this deviates from the I²C version).
The end of a request or reply is signaled by a period of silence, called t3.5 by the ModBus specification. See below for recommendations on its length.
The status byte can have these values:
| Value | Meaning | Result bytes |
|---|---|---|
| 0x00 | COMMAND_OK |
Command-specific |
| 0x01 | COMMAND_FAILED |
Command-specific |
| 0x02 | COMMAND_NOT_SUPPORTED |
None |
| 0x03 | INVALID_TRANSFER |
None |
| 0x04 | INVALID_CRC (I²C only) |
None |
| 0x05 | INVALID_ARGUMENTS |
None |
| 0xff | Unused |
When multiple reads happen in succession, each should return the same data. This allows the master to re-try a read when it detects a CRC error in the reply, without having to re-issue the command again.
Any multi-byte values specified in this protocol should be transmitted in network order (big endian), so with the most significant byte first. As an exception to this, the CRC on RS485 messages is transmitted little-endian, for compatibility with the Modbus protocol.
The child is allowed to apply clock stretching at any time during a transaction in order to process the command given or for other reasons. This includes the entire write and read, to allow for example the child to execute the command either directly after receiving it, after seeing a stop condition or only during the read just before sending its reply.
The total clock stretching that may be applied by the child during an entire transaction is 80ms. Having a maximum stretch time allows the master to detect a timeout and abort the transaction. The master is also allowed to stretch the clock, no bounds are imposed on that. The child should not attempt to detect a timeout itself, but instead rely on the master. The child should instead monitor the bus for a start condition, to always allow the master to start a new read or write.
On I²C, the master can retry a failed read, for example when a CRC error occurs on read. On subsequent reads, the child will return the exact same reply.
On RS485 replies are initiated by the child, not the master, and there is no mechanism for re-requesting a reply a second time (to keep the child implementation simple and allow sharing a single buffer between the incoming request and an outgoing reply). This means that on CRC errors or reply timeouts, the reply must be considered lost and the master should retry the command instead (all commands are specified in such a way that this should always be possible).
On RS485, when a child detects a CRC error, it must not send an
INVALID_CRC reply, but instead drop and ignore the request. This
prevents a situation where a request is sent to child A, but is received
with a bit error in the address byte by child B. If child A does receive
the request correctly, then both childs might think the request is for
them and send conflicting replies. To prevent this, a reply should only
be sent when the CRC is correct. This means that bit errors in the
request will result in a master timeout.
The child must start sending their response within 80ms. More specifically, this is the maximum time between the end of the inter-frame interval (t3.5) and the start bit of the first response byte.
If no response is sent within that time (plus some margin), the master should assume that the response was lost and will no longer be sent and should act accordingly (i.e. retry or report failure). If a child finalizes a reply only after this timeout, it should drop it rather than send it too late, to prevent bus contention.
Note that this maximum response time was chosen to be long enough to allow a full page erase and write on a STM32G0 MCU (using fast programming), to prevent needing the additional (protocol and implementation) complexity of polling for completion. If future implementations need longer response times, the maximum response time could be extended, or additional polling mechanisms could be added.
When multiple children are connected to the same bus, a muster must have some ways to distinguish them.
There are currently two ways to achieve this:
-
By using the "Hardware type" field of the
SET_ADDRESScommand. This allows the master to reconfigure the address of a single child based on its hardware type before further querying it. A big limitation of this approach is that it only works when all children have unique hardware types, and it also requires "blindly" reassigning addresses for each hardware type that might be present before knowing that a device is actually present.This approach was implemented for the I²C version of this protocol, but never actually used in practice (since only one device was present on the bus anyway).
-
By using "child select" pins. These are similar to the Chip Select pins used in the SPI interface, where the bootloader only responds to commands to the initial address range when its child select pin is asserted. Commands addressed to the address configured by
SET_ADDRESSand general call commands are processed unconditionally.This requires an extra wire to be routed to each child, but application firmware typically already requires a status or irq pin which can be reused as a child select pin (which is used in the master-to-child direction when the bootloader runs and is used in the child-to-mastr direction when the application firmare runs). To prevent short-circuits when both sides accidentally drive the pin, adding a series resistor is recommended.
This pin is intended to be active-low open-collector with a pullup on the master side (though push-pull can also be used, with a slightly higher chance of conflicts).
The pin must be kept asserted or deasserted throughout the entire transaction, if the pin status is changed halfway through a transaction, it is undefined whether the child will respond or not.
When its child select pin is not asserted, a child is allowed to respond with ACKs to an I²C write transaction (to simplify implementation), but it must not ACK the subsequent read transaction.
To simplify wiring, children can also be connected in a tree topology, where any child may have downstream connectors to connect additional "nested" children to the bus. Each of these downstream connectors contains a distinct child select pin, each of which can be asserted individually using the
SET_CHILD_SELECTcommand.It is expected that the application firmwares further support this topology by providing a
GET_STATUS_PINSor similar command to query the value of each downstream status pin, and will assert their upstream status pin when any downstream status pin is asserted.This toplogy means that the master only needs a single child select pin for each directly-connected child, at the expense of some additional overhead accessing the child select or status pins.
To enumerate the bus, the master starts by deasserting all child select pins and issues a general call reset (which causes all children to deassert their downstream child select pins). Then, it asserts one child select pin, discovers if any child is connected, reconfigures its address and deasserts the pin again. This process is repeated for all of its own child select pins, as well as any child select pins on the discovered children, allowing it to discover all connected children as well as how they are connected physically.
Note that the first option (using hardware type) is always available in compliant bootloader implementations. However, there is no in-band mechanism for deciding or detecting if the child select mechansim is in use, so this must be coordinated based on the system design. For new designs, the child select mechanism is recommended because it gives the greatest flexibility.
For 3devo, the I²C-based systems will remain configured to not use the child select mechanism (and probably be limited to a single device anyway). All future developments will use the RS485 transport and are intended to have child select enabled.
Instead of responding to a single address, the child will respond to a
range of different addresses. Even though this increases the chance of
one of these addresses colliding with other devices (i.e. other I²C or
other ModBus devices) in the system, there is only a small chance that
all of these addresses collide. The protocol includes a SET_ADDRESS
command that makes the child respond to just a single address, after
which all other addresses can be used as normal without conflicts.
The bootloader will initially respond to any address in the 8-15 range.
For I²C, the protocol uses CRC-8-CCITT, which should provide protection against all 1-bit and 3-bit errors, and good protection for 2-bit errors up to the maximum message size. See the publication by Philip Koopman for CRC comparisons. This CRC was mostly chosen because an efficient AVR implementation is available and it seems to perform well enough.
Polynomial: x^8 + x^2 + x + 1 (0x83 / 0xE0) Starting value: 0xff No output XOR
For RS485, the protocol uses CRC-16-IBM, as used by ModBus.
Polynomial: x^16 + x^15 + x^2 + 1 (0xC002 / 0xA001)
Starting value: 0xffff
No output XOR
PyCRC command: pycrc --model crc-16-modbus --check-hexstring 'DEADBEEF'
The child is assumed to have a small and fixed bootloader, which implements a single version of this protocol. The master is assumed to be more complex and easily upgraded, and will typically support all versions up to the current version.
This means that a newer master with an older child should always work, since the master has explicit support for older protocol versions. When an older master (e.g. older firmware on the master) is running against a newer child, things should just work if possible, but at least allow an error message to be shown.
This protocol is initially designed to talk to a microcontroller on the
interface board. This microcontroller needs to take action to enable the
display before an error message can be shown to the user, so this protocol
contains some special provisions for this case (e.g. the POWER_UP_DISPLAY
command).
Additionally, the following rules apply:
- All future version of this protocol, should implement at least the
GET_PROTOCOL_VERSION,SET_ADDRESSand, if appropriate, thePOWER_UP_DISPLAYcommands, as specified in the 1.0 version of this protocol. All other commands can be changed in any way (including different framing, checksums, etc.), provided the protocol version is bumped appropriately. - Whenever a change is made that would cause a master implementing an older version of the protocol to stop working (commands no longer working or not having the intended effect), the major protocol version should be increased.
- For all other changes, such as adding new commands or arguments, the minor protocol version is increased.
For the master, this means that it can always send the three commands mentioned above, and any other commands must be sent after establishing the protocol version in use (provided the master knows about it). If the master knows about the major protocol version, but the minor protocol version is higher that what it supports, the master can just assume the minor version is the highest one it supports.
When processing replies, the master should be tolerant of unexpected values and extra bits (ignore them if possible). If this behaviour would break things (e.g. a new reply value that requires the master to act differently), the major version should be bumped, otherwise only the minor version would suffice. Note that adding extra bytes to a reply always requires bumping the major version, since (on I²C) the master dictates how much bytes are read.
The bootloader is intended to allow uploading an application into flash and to start it. The intention is that on every startup, the master uploads an application (with the child taking care to prevent an erase-write cycle if the same application is uploaded twice). For this reason, the bootloader has no timeout value and does not start the application unless explicitely instructed.
This means that the application that is run (after being uploaded by the master) is strongly tied to the master application. This removes all need for protocol compatibility between application versions, or between the bootloader and the application. The only thing the application must support is the general call reset command (see the generall call section elsewhere in this document).
However, it is encouraged for the application to use the same framing
format (write/read pairs, checksum, timeout constraints, command and
status codes, etc.). Any commands that make sense (e.g.
SET_ADDRESS) can also be implemented, new commands should be
defined in the range reserved for application commands.
An application firmware is also encouraged to implement the
GET_PROTOCOL_VERSION command to allow identifying a successfully
started application firmware using a generic command, as well as
distinguishing a running bootloader from an application with a single
command if needed.
If the application firmiware implements GET_PROTOCOL_VERSION, it
should return a version of 0.0 (0x00, 0x00).
The bootloader and the application should support the general call address (0x00), and in particular the reset and reset address commands.
On I²C, a general call consists of a write to the 0x00 I2c address, followed by a command byte. No additional framing (e.g. no CRC) happens, and no reply is read in response to the command. The command byte uses the standard I²C meaning of 0x04 for "reset address" and 0x06 for reset.
On RS485, a general call consists of a full frame consisting of the 0x00 address, the commandcode and 2 CRC bytes. The command bytes are 0x44 for "reset address" and 0x46 for "reset". These are arbitrary values chosen from a "user-defined function codes" block in the Modbus specification to minimize chance of conflicts with other Modbus servers that also listen to the general call command.
The reset address command (0x04/0x44) should revert the effect of the
SET_ADDRESS command and make the bootloader respond to the default
addresses again. If the application also implements SET_ADDRESS or
something similar, it is recommended to also implement the reset address
command.
The reset command (0x06/0x46) should do a hardware reset of the child (which should start the bootloader again and as a side effect reset the address as well).
The master should always send a general call reset command at startup, which serves to get all children into a known state, running the bootloader. This prevents issues when the master resets, while the child does not, resulting in the child running application code while the master needs to talk to the bootloader.
The base protocol defines these commands:
| Value | Meaning |
|---|---|
| 0x00 | GET_PROTOCOL_VERSION |
| 0x01 | SET_ADDRESS |
| 0x02 | POWER_UP_DISPLAY |
| 0x03 | GET_HARDWARE_INFO |
| 0x04 | GET_SERIAL_NUMBER |
| 0x05 | START_APPLICATION |
| 0x06 | WRITE_FLASH |
| 0x07 | FINALIZE_FLASH |
| 0x08 | READ_FLASH |
| 0x09 | GET_HARDWARE_REVISION |
| 0x0a | GET_NUM_CHILDREN |
| 0x0b | SET_CHILD_SELECT |
| 0x0c | GET_MAX_PACKET_LENGTH |
| 0x0d | GET_EXTRA_INFO |
| 0x80 - 0xfe | Reserved for application commands |
| 0xff | Reserved |
This command returns the protocol version implemented by the child split into a major and minor part. For example, version 1.0 would be 0x01, 0x00, while version 10.2 would be 0x0a, 0x02.
When this command is implemented by an application firmware, it should always return a version of 0.0 (0x00, 0x00).
See the section on compatibility on how the master is expected to handle this version number.
| Bytes | Command field |
|---|---|
| 1 | Cmd: GET_PROTOCOL_VERSION (0x00) |
| 1/2 | CRC |
| Bytes | Reply format |
|---|---|
| 1 | Status: COMMAND_OK (0x00) |
| 1 | Length |
| 1 | Major version |
| 1 | Minor version |
| 1/2 | CRC |
This command allows changing the address, to prevent conflicts with other devices.
| Bytes | Command field |
|---|---|
| 1 | Cmd: SET_ADDRESS (0x01) |
| 1 | Address to use |
| 1 | Hardware type |
| 1/2 | CRC |
| Bytes | Reply format |
|---|---|
| 1 | Status: COMMAND_OK (0x00) |
| 1 | Length |
| 1/2 | CRC |
On I²C, the address given is the 7-bit address, where the MSB is ignored by the child and must be set to 0 by the master. On RS485, the address is just the full 8-bit address.
The device type is a selector to select only devices of a particular type. This can be used when multiple devices share the same bus and respond to the same address, so they can still be disambiguated based on their device type.
When a child receives this command containing a hardware type that does
not equal its own type (as returned by GET_HARDWARE_INFO), it should
completely ignore the command (and not respond to the subsequent read
request either).
A device type of 0x00 is a wildcard, all devices should process that. Masters should only use this when they are certain that at most one device will be respond, since there is no provision to handle conflicts.
On I²C, the change in address can happen either before or after the response is read. The master should read a response from the old address, and if no reply is received, it should read from the new address.
On RS485, the response should include the old address from before the switch.
This command is intended specifically for the interface board, and serves as a fallback in case the master cannot normally upload a firmware and power up the display using that (because the bootloader protocol is too new, or uploading repeatedly fails, etc.). When this command is given, the bootloader executes the proper sequence for powering up the on-board display. No initialization commands are sent to the display, this should be done by the master.
By using clock stretching (for I²C) or delaying the reply (for RS485), the child should ensure the transaction does not complete before the display is powered on and ready.
| Bytes | Command field |
|---|---|
| 1 | Cmd: POWER_UP_DISPLAY (0x02) |
| 1/2 | CRC |
| Bytes | Reply format |
|---|---|
| 1 | Status: COMMAND_OK (0x00) or COMMAND_NOT_SUPPORTED (0x02) |
| 1 | Length |
| 1 | Controller type |
| 1/2 | CRC |
Modules that do not have an on-board display should just return
COMMAND_NOT_SUPPORTED.
The result includes single controller type byte, which indicates the type of display controller attached. Currently only one type is defined: 0x01 to indicate an SSD1306 or compatible controller.
This command is intended as a last-resort option, since the powerup-sequence is hardcoded and might not be ideal.
This command requests information about the hardware the bootloader runs on.
| Bytes | Command field |
|---|---|
| 1 | Cmd: GET_HARDWARE_INFO (0x03) |
| 1/2 | CRC |
| Bytes | Reply format |
|---|---|
| 1 | Status: COMMAND_OK (0x00) |
| 1 | Length |
| 1 | Hardware type |
| 1 | Compatible hardware revision |
| 1 | Bootloader version |
| 2 | Available flash size |
| 1/2 | CRC |
The following hardware types are defined:
| Type | Meaning |
|---|---|
| 0x00 | Reserved for wildcard in GET_I2C_ADDRESS command |
| 0x01 | Interface board |
| 0x02 | Granulate processor hopper board |
The compatible hardware revision field indicates the oldest revision
that this board is compatible with and may not reflect the actual board
revision. A board is compatible with another revision, if anything (i.e.
firmware) that is intended for the older version, will also work for the
newer board. In practice, this means a newer version only has minor
hardware optimizations, small improvements or additions that can be
ignored by older firmware. To obtain the actual hardware version, use
the GET_HARDWARE_REVISION command.
The hardware revision is split into a major and minor version. The upper 4 bits indicate the major version, while the lower 4 bits indicate the minor version. For example, 0x15 means revision 1.5, while 0x2f means revision 1.15.
The only exception is that interface board (type 0x01) version 1.3 should use a compatible hardware version value of 0x01, if compatibility with protocol version 1.0 is intended.
The bootloader version value is informative (and should be considered board-specific) and its value is not defined by this specification.
The available flash size indicates the number of bytes of flash that are available to write to.
The max message size indicates the largest I²C message that can be sent or received (including the checksum, excluding the address byte).
This command requests the actual hardware version of the board.
| Bytes | Command field |
|---|---|
| 1 | Cmd: GET_HARDWARE_REVISION (0x09) |
| 1/2 | CRC |
| Bytes | Reply format |
|---|---|
| 1 | Status: COMMAND_OK (0x00) |
| 1 | Length |
| 1 | Hardware revision |
| 1/2 | CRC |
The returned hardware revision indicates the actual board version and
should be changed on every hardware change, even minor changes. Together
with the compatible hardware revision returned by the
GET_HARDWARE_INFO command, the master can determine whether it
supports this hardware version.
The hardware revision is split into a major and minor version. The upper 4 bits indicate the major version, while the lower 4 bits indicate the minor version. For example, 0x13 means revision 1.3, while 0x2f means revision 1.15.
This command was added in protocol version 1.1.
This command requests the serial number of the board, if available. If
no serial number is present, this command can return
COMMAND_NOT_SUPPORTED.
| Bytes | Command field |
|---|---|
| 1 | Cmd: GET_SERIAL_NUMBER (0x04) |
| 1/2 | CRC |
| Bytes | Reply format |
|---|---|
| 1 | Status: COMMAND_OK (0x00) |
| 1 | Length |
| n | Serial number |
| 1/2 | CRC |
The length and format of the serial number is device-dependent.
This command tells the bootloader to start the application. To simplify child implementation, this command returns no reply, so the application can be started immediately after receiving the command, instead of having to wait for a reply to be read first.
| Bytes | Command field |
|---|---|
| 1 | Cmd: START_APPLICATION (0x05) |
| 1/2 | CRC |
This command allows writing an application to flash.
| Bytes | Command field |
|---|---|
| 1 | Cmd: WRITE_FLASH (0x06) |
| 2 | Address |
| 0+ | Data |
| 1/2 | CRC |
The address specified indicates the (byte) address of the first byte to write. Note that this address is relative to the writable flash area, which might or might not be at the start of the device's flash (e.g. the bootloader might be at the start of flash and an address 0 might refer to the first available address after the bootloader). There is currently no mechanism to query for such a "flash offset". When relevant (e.g. for selecting the right image to flash), the master is expected to have out-of-band knowledge (e.g. based on the device type, hardware version, bootloader version, etc.) to determine the offset.
To simplify the child implementation, this command should only be used
to write consecutive bytes to flash, starting at address 0. In
particular the address must either be one past the last byte written, or
it must be zero to start, or start over. If this constraint is violated,
the child should return INVALID_ARGUMENTS and otherwise ignore the
packet (so the next write should be accepted if it is consecutive with
the previous valid write). This allows the master to retry a write when
it receives in invalid checksum on a reply. It should then ignore the
INVALID_ARGUMENTS error on the retry.
Writing to flash in this way guarantees that the sent bytes are (eventually) written, but the rest of the flash contents becomes undefined (e.g. parts of it will likely be erased).
Due to flash page sizes, the data sent might not be written immediately,
but is typically buffered until a full flash page can be written (and is
then automatically written). At the end of flashing, the
FINALIZE_FLASH command must be given to commit any remaining bytes to
flash.
When the bytes sent are identical to the current content of the flash, the child should prevent an erase-write cycle. This allows the master to send write commands on every startup, without danger of wearing out the flash contents.
| Bytes | Reply format |
|---|---|
| 1 | Status: COMMAND_OK (0x00) |
| 1 | Length |
| 1/2 | CRC |
| Bytes | Reply format |
|---|---|
| 1 | Status: INVALID_ARGUMENTS (0x05) |
| 1 | Length |
| 1/2 | CRC |
| Bytes | Reply format |
|---|---|
| 1 | Status: COMMAND_FAILED (0x01) |
| 1 | Length |
| 1 | Reason |
| 1/2 | CRC |
When flashing fails for any reason, an additional reason byte is returned. The meaning of this byte is purely informative and not defined by this protocol, its meaning should be looked up in the bootloader.
This command commits all unwritten bytes (as sent by WRITE_FLASH) to
the the flash memory. After this command, no further WRITE_FLASH
commands should be sent, except with a zero address to start over.
| Bytes | Command field |
|---|---|
| 1 | Cmd: FINALIZE_FLASH (0x07) |
| 1/2 | CRC |
| Bytes | Reply format |
|---|---|
| 1 | Status: COMMAND_OK (0x00) |
| 1 | Length |
| 1 | Erasecount |
| 1/2 | CRC |
| Bytes | Reply format |
|---|---|
| 1 | Status: COMMAND_FAILED (0x01) |
| 1 | Length |
| 1 | Reason |
| 1/2 | CRC |
The erasecount is the number of pages erased since the last reset, or
the last succesful FINALIZE_FLASH command. This is returned to
facilitate verification of the "erase only when needed" mechanism.
When flashing fails for any reason, an additional reason byte is returned. The meaning of this byte is purely informative and not defined by this protocol, its meaning should be looked up in the bootloader.
This command reads the specified number of bytes from the specified
address and returns them. This reads the current state of flash, so when
this is given between WRITE_FLASH and FINALIZE_FLASH, it might
return an inconsistent state.
| Bytes | Command field |
|---|---|
| 1 | Cmd: READ_FLASH (0x07) |
| 2 | Address |
| 1 | Length |
| 1/2 | CRC |
| Bytes | Reply format |
|---|---|
| 1 | Status: COMMAND_OK (0x00) |
| 1 | Length |
| 0+ | Data |
| 1/2 | CRC |
This command returns the number of downstream child connectors and/or child select pins this child has.
This command is optional, if it is not implemented,
COMMAND_NOT_SUPPORTED should be returned and the master should behave
as if a value of 0 was returned.
| Bytes | Command field |
|---|---|
| 1 | Cmd: GET_NUM_CHILDREN (0x0a) |
| 1/2 | CRC |
| Bytes | Reply format |
|---|---|
| 1 | Status: COMMAND_OK (0x00) |
| 1 | Length |
| 1 | Number of children |
| 1/2 | CRC |
This command was added in protocol version 2.1.
This command sets the status of a downstream child select pin.
This command is optional, but if GET_NUM_CHILDREN is implemented,
SET_CHILD_SELECT must also be implemented.
| Bytes | Command field |
|---|---|
| 1 | Cmd: SET_CHILD_SELECT (0x0b) |
| 1 | Index |
| 1 | State |
| 1/2 | CRC |
The specified index is the index of the pin to control, which must be
greater than or equal to 0, and less than the number returned by
GET_NUM_CHILDREN.
The specified state is the intended state of the pin: 0 to deassert the pin (make it Hi-Z), 1 to assert the pin (make it LOW).
If arguments outside these ranges are specified, INVALID_ARGUMENTS
will be returned.
| Bytes | Reply format |
|---|---|
| 1 | Status: COMMAND_OK (0x00) |
| 1 | Length |
| 1/2 | CRC |
| Bytes | Reply format |
|---|---|
| 1 | Status: INVALID_ARGUMENTS (0x05) |
| 1 | Length |
| 1/2 | CRC |
This command was added in protocol version 2.1.
This command returns the maximum length of a request or reply packet that the bootloader is prepared to accept or return.
What is included in the packet length depends on the protocol used:
- For I²C, this is all data, including the CRC but excluding the address which is considered part of the underlying I²C protocol.
- For RS485, this includes all data including the address, up to and including the CRC.
This command is optional, if it is not implemented,
COMMAND_NOT_SUPPORTED should be returned and the master should behave
as if a value of 32 was returned.
If this command is implemented, the value returned must be at least 32 (in other words, a master may assume that 32-byte packets are ok, even without using this command).
| Bytes | Command field |
|---|---|
| 1 | Cmd: GET_MAX_PACKET_LENGTH (0x0c) |
| 1/2 | CRC |
| Bytes | Reply format |
|---|---|
| 1 | Status: COMMAND_OK (0x00) |
| 1 | Length |
| 2 | Max packet length |
| 1/2 | CRC |
This command was added in protocol version 2.1.
This command requests additional information about the board, typically
about the hardware. It can be used to supply more detailed information
than just the board version returned by GET_HARDWARE_REVISION, for
example about attached hardware, or about different variants of the same
board with different component values.
The meaning of the bytes depends on the board type, and might become dependent on hardware revision, protocol version and/or bootloader revision in the future.
For compatibility with future changes, the master should ignore any bytes it did not expect, and provide an error when a byte that it does expect has an unexpected value.
When changes to the meaning of these bytes (changing byte values, adding byte values, adding new bytes) would cause an older master to misbehave (stopping with an error is ok), ether the compatible hardware revision or the major protocol error must be bumped to force the master to error out instead.
The maximum number of reply bytes is 16. A master should always be prepared to handle up to 16 bytes, even when it expects a smaller reply based on the board type, to ensure it will stay working when additional bytes are added later.
This command is optional, if a board has no additional info to return,
it can return COMMAND_NOT_SUPPORTED instaed.
For the interface board (hardware type 0x01), the returned bytes are as follows:
| Bytes | Command field |
|---|---|
| 1 | Display type |
The display type values are as follows:
| Value | Display type meaning |
|---|---|
| 0 | Reserved |
| 1 | Reserved for original display module on interfaceboard <= 1.2 |
| 2 | Wisechip UG-2864ASWPG01, display used on interfaceboard >= 1.3 |
| 3 | Electronic Assembly EA OLEDM128-6LWA, alternative display used on interfaceboard >= 1.5 |
For the hopper board (hardware type 0x02), no extra info is defined.
This command was added in protocol version 2.1.
- Version 1.0
- Initial version.
- Version 1.1
- Redefined the hardware revision field to be the compatible hardware revision field instead and generalize its meaning to a major/minor format.
- Added
GET_HARDWARE_REVISIONcommand.
- Version 2.0
- Extend maximum clock stretch time to 80ms. This needs a major version bump, since older masters might timeout at the previous value of 35ms.
- Version 2.1
- Add support for RS485.
- Add support for child select pins (added
GET_NUM_CHILDRENandSET_CHILD_SELECTcommands and support responding only when child select pin is asserted). - Renamed to Childbus protocol.
- Add
GET_MAX_PACKET_LENGTHcommand. - Add hopper board hardware type.
- Add
GET_EXTRA_INFOcommand.
Permission is hereby granted, free of charge, to anyone obtaining a copy of this document, to do whatever they want with them without any restriction, including, but not limited to, copying, modification and redistribution.
NO WARRANTY OF ANY KIND IS PROVIDED.