Problem with Leveling with JZ-TS28 and others question

[Sharkys80]

Hi

I have a Problem with Leveling with JZ-TS28 , my 3D touch dosnt work with the Display.
Without the Display its works fine. After the first Point the Sensor don't deploy.
Is the Leveling Option on Display not G28 &G29??

No language support in German for the 2.8 only for 3.5?

Any Code for botton Sends open the serialconsol i dont find the correct code in the list. I try build Gode M122 and i need the feedback from the TMC ?Or where i found the complet list for local instruction (7001 ~ 7999)???

And the last question :any other option to buy a 3,5 or 4 display from taobao site?

[miblooming]

Hi 1. 3D touch The leveling of jz-ts28 is manually. Moving to points, waiting you to adjust the screws of bed. If you want to use g28&g29, please add a button to send gcode of g28&g29 by UIEditor. https://github.com/miblooming/JZ-TS24-2/tree/master/JZHelper_ui_editor/JZ-TS24-3____(2.4%262.8)/JZ-TS24-3____(2.4%262.8)_landscape 2.Yes there's no German for the 2.8 3.Two method: A) Send gcode by Gcode Common Line, HomePage -> My Tools -> Gcode B)Add buttons to send gcode by UIEditor. 4.Pay me by paypal, and I'll ship the product to you. Best Regards LoomingXu  

…

------------------&nbsp;原始邮件&nbsp;------------------ 发件人:&nbsp;"Sharkys80"<[email protected]&gt;; 发送时间:&nbsp;2020年1月14日(星期二) 下午5:11 收件人:&nbsp;"miblooming/JZ-TS24-2"<[email protected]&gt;; 抄送:&nbsp;"Subscribed"<[email protected]&gt;; 主题:&nbsp;[miblooming/JZ-TS24-2] Problem with Leveling with JZ-TS28 and others question (#28) Hi I have a Problem with Leveling with JZ-TS28 , my 3D touch dosnt work with the Display. Without the Display its works fine. After the first Point the Sensor don't deploy. Is the Leveling Option on Display not G28 &amp;G29?? No language support in German for the 2.8 only for 3.5? Any Code for botton Sends i dont find the correct code in the list i try build Gode M122 and i need the feedback from the TMC ? And the last question :any other option to buy a 3,5 or 4 display from taobao site? — You are receiving this because you are subscribed to this thread. Reply to this email directly, view it on GitHub, or unsubscribe.

[miblooming]

It's for JZ-TS35/40, some codes are not enable on jz-ts28

https://github.com/miblooming/JZ-TS24-2/blob/master/JZHelper_ui_editor/JZ-TS35WIFI___(3.5%264.0)/API_for_wifi.txt

[Sharkys80]

Thank you for the answers.
But yesterday a start a test with only printing from SD:
So my normal config is UBL is on and setup is complet in Marlin+Simplify3D(start script) + Save UBL mesh values to EEPROM on LPC1768 but when i start.He ignored the the start script wit G28 & G29 J in the gode, the Z axis dosnt compensate its self. printig without Display with only a REPRAP_DISCOUNT_FULL_GRAPHIC_SMART_CONTROLLER its work fine .What is the failure?

[miblooming]

Can you show me the command lines at beginning of Gcode file?

[Sharkys80]

removed

[miblooming]

Maybe there's a compatibility issue with 3D touch.
I'll try to fix it. But no that quickly.

[Sharkys80]

OK i can wait thank you, but i will test a Inductive sensor on my second printer. I guess that dosent work too.

[Sharkys80]

So i tested with my 2 printer Melziboard 2.0 and Inductive sensor: You have right, there's a compatibility issue with 3D touch the other Sensor work fine with ABL and display. I hope for fix